(Working time：
9:00-18:00 GMT+8)
Hot line0086-757-82711390
(Working time：
9:00-18:00 GMT+8)
Hot line0086-757-82711390
 |
|
0086-757-82711390
|
 |
Position：Home > Products |  |
 |
|
|||||||
| Introduction |
High temperature silicone sealant,rtv silicone sealant,
electrical electronic adhesive glue sealant ,
heat resistant silicone sealant
HOMEEN is a leading silicone sealant manufacturer ,we mainly produce neutral one component electronic silicone sealant for consumer electronics ,for example ,conduction cooker ,oven ,fridge ,iron,etc .
We also produce two component potting compound for LED power driver ,and potting compound for LED display .
HOMEEN provide whole solution for LED ,solar PV ,consumer electronic ,automobile ,craft ,etc .
High temperature silicone sealant HM-2441
APPLICATIONS
1. Major used in heat resisting elements as potting adhesive (such as Automobile Parking Sensor)
2. Other hear resisting elements need potting adhesive
PROPERTY
1. Single part, neutral, room temperature cured sealant. Low viscosity, with certain flowability.Without any obvious odour when curing, easy to apply.
2. Suitable for general structure of electronics, used as potting adhesive and insulating material. No corrosion to most metal (except copper)
3. Have strong adhesive
4. Excellent resistance of extreme temperature, and an-ti acid, base, salt, and lube oil.
PARAMETER
|
Color |
subtransparent,white,black |
Viscosity (mpa·s)25℃ |
10000~12000 |
|
Specific gravity |
1.16g/cm3 |
Durometer Shore A |
32 |
|
Tensile strength |
0.8Mpa |
Shear strength |
0.6Mpa |
|
Elongation |
150% |
Application temperature (℃) |
–50~+200 |
|
Breakdown voltage |
16kv/mm |
Volume resistivity |
5.1ⅹ1014Ω•CM |
|
Dielectric constant |
2.8(1MHz) |
Tack-free time |
30mins（20℃，50% RH） |
PACKAGING
Cartridge 300ml/pc
STORAGE AND SHELF LIFE
Silicone encapsulant should be stored at -20℃~27℃.Our sealant has a usable life of 9 months when stay unopened.
REMARK
Completely cured sealant is non-toxic, but do not directly contact with eyes or kids. Should keep ventilate when applying. We suggest that before applying, customer had better have a test to make sure our sealant can highly meet your demand.
Attention
1.This adhesive condense to cure with ratio 10:1 for part A and part B completely mixed. If require shorter or longer cure time which can be reach via adjusting ratio of both components.Normally,we don’t suggest heating, which can result in generating small bubble or pinhole, which have bad effect on appearance and sealing.
2.We suggest that potting thickness should not more than 50mm,normally thickness of 20mm,can release the bubble by staying still for a while. If require thick potting area, should at least put this mixed adhesive into vacuum container and at 700mmHg for at least 5 minutes.
3. Completely mix two components
4.If require mat effect,pls add the C component, and only after 24-48h of potting, the mat effect comes out.Relatively,higher temperature can accelerate the mat effect, but keep in mind, should be lower than 50C.
5. Color depends on customer’s requirement.
Test
We suggest that customers should test this product before application and see if it could meet the demand.
Shelf life
Store under 30C and stay sealed
Shelf life of component A and B is 12 months after the date of manufacture.
Tensile strength/Mpa1.5
Elongation at break/%
84
Dielectric strength/kV/mm
18
Thermal conductivity/W/m/K
0.7~0.9
Waterproof Rating IP65
Note: This product is subject to curing temperature, the temperature is higher, the operation and full curing time will be shorter.
workmanship
Mixing A,B parts according to proportion A:B=10:1 on the basis of weight or volume until evenly. Suggest to stir A and B part respectively before mixing them to make it uniform distribution. Then dispense the adhesive on the potting position. If need high-thermal conductivity vacuum deaeration
is necessary otherwise no need. It can be cured at room temperature or by heating. But it is featured of room temperature curing, there is summertime and wintertime types, the two types are sthe same except for the operation time.
Note:
This silicon rubber is vulcanized by platinum catalys, the nitrogen, sulfur, phoshor and rgano-tin compound material may hinder its vulcanization, so please clean the rosin on the PCB and use the soldering tin with low lead content.
Packaging:40kg/set。
Storage period:sealed under 30C, the A,B parts shelf life are 9 nine months after production. Thereare sediments come after 3 months,please mix it thorough eveness before using.
$n-8;: 88 0%;font-family:宋体;mso-ascii-font-family: "Times New Roman";mso-hansi-font-family:"Times New Roman";mso-bidi-font-family: 宋体;mso-font-kerning:0pt'>·s
2000-2500
3500-4000
Specific gravity
1.55
Curing time
4-5h/28C，1h/80C
Operation time
40-60min/25C
Shore Hardness /A
55-60
Dissipation factor
0.003
Shrinkage percentage %
0.3-0.5
Flame retardant rating
UL94-V1
Dielectric constant
3.0
Volume resistivity/Ω·cm
1015
Tensile strength/Mpa
1.5
Elongation at break/%
84
Dielectric strength/kV/mm
18
Thermal conductivity/W/m/K
0.7~0.9
Waterproof Rating
IP65
Note: This product is subject to curing temperature, the temperature is higher, the operation and full curing time will be shorter.
workmanship
Mixing A,B parts according to proportion A:B=10:1 on the basis of weight or volume until evenly. Suggest to stir A and B part respectively before mixing them to make it uniform distribution. Then dispense the adhesive on the potting position. If need high-thermal conductivity vacuum deaeration
is necessary otherwise no need. It can be cured at room temperature or by heating. But it is featured of room temperature curing, there is summertime and wintertime types, the two types are sthe same except for the operation time.
Note:
This silicon rubber is vulcanized by platinum catalys, the nitrogen, sulfur, phoshor and rgano-tin compound material may hinder its vulcanization, so please clean the rosin on the PCB and use the soldering tin with low lead content.
Packaging:40kg/set。
Storage period:sealed under 30C, the A,B parts shelf life are 9 nine months after production. Thereare sediments come after 3 months,please mix it thorough eveness before using.
|
| silicone cookware handle |
|
|
| stainless steel cookware handle |
|
|
| diecasting pan handle |
|
|
| cookware handles for pan and pot |
|
|
| cookware handle, cookware parts |
 |
|
广东皓明有机硅材料有限公司 Tel：0086-757-82711390 Fax：0086-757-82711390 E-mail：marketing1@hm-sil.com Add：Lianhua Development Zone,Dinghu District,Zhaoqing City,Guangdong,China. |
