High Refractive Index Silicone LED Encapsulant HM-7101 Key：High Refractive Index Silicone LED Encapsulant ,High purity silicone potting sealant for LED Encapsulation adhesive​​​ Characteristic： High Refractive Index Silicone LED Encapsulant ,High purity silicone potting sealant for LED ,Encapsulation adhesive​​​;with 1.53 refractive index. Normally used as potting adhesive in LED patch, and high and low power LED module encapsulation like 3014、3528、5050、5630 … Hotline：0086-757-82711390

High Refractive Index Silicone LED Encapsulant ,High purity 

silicone potting sealant for LED Encapsulation adhesive

Haoming is a leading chinese manufacturer for one component and two components silicone sealant ,which are widly used in craft ,LED,Solar PV ,consumer electronics ,automobile,etc.Our products include silicone rubber, RTV-2 mold making silicone, RTV liquid silicone rubber,thermal conductive silicone potting compound,electronic silicone conformal coating,silicone encapsulant,electronic silicone sealant,general purpose neutral silicone sealant,gasket silicone sealant .For more information about our silicone sealant ,pls contact

Mandy 

HM-7101A/B

Directions：

The HM-7101A/B is formed by two parts potting adhesive, with 1.53 refractive index. Normally used as potting adhesive in LED patch, and high and low power LED module encapsulation like 3014、3528、5050、5630 surface mount devices,this binding agent has good adhesive strength for PPA, PCB and metal material.

Parameters：

Instructions for use：

Use the A、B parts according to their mass proportion of 1:1 and conduct the production in the dried and dust-free cirsumstance.

Before adhesive dispensing please clean the bracket thoroughly to get rid of the material which may hinder curing of adhesiv from the baseplate

Stir by Planetary gravity mixer to make it uniform mixing or emove air bubbles from the adhesive at 45℃ temperature with 10mmHg vacuum deegree before using

 The bracket should be heated at 150℃ for 30 minutes for dehumidification before injection adhesive, and dispense adhesive before the rack absorb moisture again.

Heat the bracket in a 80℃ oven for 1hr then take to another 150℃ oven bake for 2-4 hours it will be full cured.

Put the untapped adhesive into the spotless container for later use

Notes：

HM-7101A/B is Addition type siliconeelastome,which should not touch  some material alkyne,lead,tin,cadmiu,mercury and other heavy metal which may cause uncured or partialy cured.The potting suface must be cleaned before sealing and filling.

Different operation will result in various consequences may lead to bubble,barrier,debonding,crack etc. Please refer to associated personel to avoid above occurrenc.

Better the vacuumizer is an open system and never use for epoxy resin.The best way is to establish a dedicated organic silicon production line.

Please use appropriate container and stirring rod for mixing. And don’t wear silicon glove to get touch the silicon.

Because it is not easy to get rid of the bubbles from the organic silicon during operation, please heat up starting from room temperature while removing the buttbles.

In case the cememtation is not good generally it is owing to not full vulcanization can not adhere to the object, you can increase the temperature or heat it longer to improve the cememtation.

Due to the condistion and method is out of our control, this file can not be used to replace test,in case there is any query for the material whether hinder curing,just conduct a small compatibility test to ascertain its appropriateness for special application or consult our company technical staff

High Refractive Index Silicone LED Encapsulant ,High purity 

silicone potting sealant for LED Encapsulation adhesive

Storage and transportation:

Keep in dark and dried place in room temp.

Expiration date 6 months. If all technical tests remian ok after expiration date it can be used normally as well.

This product can be shipped as non-dangerous chemicals

A,B parts should be sealed for storage,don’t make any leakage during transporation.

packaging：

A part：0.5kg/bucket；1kg/bucket

B part：0.5kg/bucket；1kg/bucket